- AD Series and CO series products require that the Night Latch (NL) screw is installed in the exit device. Be sure this screw is installed- Exit hardware and strike must be properly mounted ..
In the AD and CO Series replacement parts guide it shows the same part number 46929295 for the 993R, 993S, and 993M. The pictures show that the 993R and 993S have a flat straight tailpiece and the ..
In the early cylindrical version of the AD-Series 993 locks, a spacer may be required for proper cylinder functionality. Effected cylinder types are PD / LD / RD / JDIf a customer is ..
MEASURE THE WOBBLE: When the lever is pressed toward the door, measure the distance of the lever return from the door, then pull on the lever and take a new measurement of the lever retu..
DETERMINE THE CAUSE: Remove the lever:Inspect the spring cage and spindle assembly:The spindel should be held firmly in place by the spring cage. You should not see any movement..
Information on low battery threshold and nuisance delay is noted below: New firmware now has improved levels.- These are approximate values/levels which change with measurement meters and measure..
AD400/AD200/AD250 After ADFwPkg 2.17.0 - June 2011 4 Battery HolderNew batteries = 6.2 VDCLow battery threshold is 4.7 VDC for SM & MT - and 3.7 VDC for MAG and PROX (USB stops working at 4..
AD400/AD200/AD250 After ADFwPkg 2.17.0 - June 2011 8 Battery HolderNew batteries = 12.4 VDC Low battery threshold is 7.2 VDC Critical battery threshold is 6.9 VDC Coin cell = new/..
CO2004 Battery Holder (ONLY) New batteries = 6.2 VDCLow battery threshold is 4.2 VDCCritical battery threshold is 3.9 VDCCoin cell = new/full is 3.0 VDC, low is 2.8 VDC
CO2504 Battery Holder (ONLY)New batteries = 6.2 VDCLow battery threshold is 4.2 VDCCritical battery threshold is 3.9 VDCCoin cell = new/full is 3.0 VDC, low is 2.8 VDC
CO200 & CO250 Disable coin cell Nuisance delay and blink,With CO.A.7 and SUS 4.10.2 or newer for CO200 and CO250, you can use the SUS/HHD, under Lock Properties, Edit, to de-select, DISABLE, t..
13 1/2' Long, 3 5/8' Wide, 1/4' Thick
There is not a coin cell on the CO100.
Use a multi-meter in series with the batteries to measure battery current. Be sure your multi-meter can accurately measure very low current, in the micro-amp range.See the attached Technical Not..
Opposite rotation of the lever is intentionally restricted by an internal block device in the spring cage this is normal operation.
Von Duprin 98/99 and 98/99XP Rim/SVR/CVR(steel door only)/Mortise exit devices are compatible with AD200, AD250, AD300, AD400, AD401-993 exit trims.
Von Duprin 22/22F Rim/SVR exit devices are compatible with AD200 and AD250-993 exit trims.
Falcon 25 Rim exit device is compatible with AD200 and AD250-993 exit trims.
The AD or CO - 993 is NOT compatible with a Von Duprin 98/99 Concealed Vertical Rod exit device on wood doors.
Causes for AA battery drain in CO-Series LOCKS - Possible Cause Fix/Corrective Actions One of the four AA batteries was inserted reversed and the reserved battery drains the other batteries. ..
CO-100 now allows the PIN code length to be changed manually. Each CO100 has a label that indicates its firmware revision. Firmware revision 2.5.0 or higher support these..
CO-100 PIN length can range from 3 digits to 6 digits with firmware version 2.5.0 and higher.
Procedure to change PIN length:1. Press {programming code (default is 97531)} then {*}.2. Press {99} then {*}, to enter Special Function Length Menu.3. Press {4} then {*}, to enter Pin Length M..
CO-100 now has NEW lock status reporting capabilities. Battery status, firmware version, hardware version and PCB serial number. See instructions below for these status menus.
The part number for the AD or CO twisted tailpiece kit is: 46929303 Tailpiece Kit - (for Exterior Escutcheon -993 into Exit Device, i.e. Von Duprin 98 or 99) Exit Trim 46929303 Includes the..
ALL AD and CO products are warranted for electrical for 1.0 year after installation OR 2.0 years after manufacture. The mfg date is on the lock stickers AND can be viewed electronically with th..
No, the CO100 is not tested with the Precision 2800, only the 21
The Schlage AD/CO trims are not compatible with the Falcon 25-V device due to the main cam on the device rotating the opposite direction for a given hand compared to the AD/CO trims output dri..
Technically no, the latch cannot be held back.But a CO lock with 50 function can lock be set to remain unlocked (lever active); this would not qualify as dogging.
The CO locks are fire rated for 3 hours.
All finished surfaces of the AD and CO lock is has the microbial finish
In the event of battery failure, the lock will fail As-Is. ( Lock remains in current state, locked or unlocked, until batteries are replaced.)
CO-Series locks, AD-Series locks, AD-Series Reader Modules, WPR400, WRI400, WSM400, TK400, CT5000, PIM400, PIM401, PIB300, and PIB301 are warranted for a period of 12 months from the date of instal..
Job Specific Warranty - If job specific warranty letters or certificates are required, please refer to the Allegion Contact Us web page and request the applicable information.NOTES:F..
AD/CO use the same template as the the 993R
The functionality of AD300 and AD400 devices is dictated by the the supported lock types of the Access Control Panel (ACP). As such, the function cannot be changed at the lock using the HHD.
The CO series locks use a standard instruction manual for all locks. The rehand drawings do not match CO100. The photos show the reader module being removed so the front plate can be removed. This ..
This information can be found at the following URL's:AD200/AD250/AD300/AD400 Cylindrical http://w3.securitytechnologies.com/irstdocs/installinstructions/102104 P516-092.pdf
This information can be found at the following URL's:AD200 http://us.allegion.com/content/dam/allegion-us-2/web-documents-2/UserGuide/Schlage_AD-200_Offline_Lock_User_Guide_-_English_102107.pdf
The original 4B battery holder used with the AD and CO Series products is updated to improve performance. The issues addressed include:- Improved spring ..
The original 4B battery holder used with the AD and CO Series products is updated to improve performance. The issues addressed include:- New ledges are added near eac..
AD and CO series -993-R model locks will work with most Von Duprin 98/99 series model push bars exit devices – Rim, CVC - Concealed Vertical Cable or CVR - Concealed Vertical Rod AD Series -200/250..
these locks with work with JD-CO6 and JD-CO7
- Von Duprin 98/99 and 98/99XP Rim/SVR/CVR(steel door only)/Mortise exit devices are compatible with AD200, AD250, AD300, AD400, AD401-993 exit trims.
- Von Duprin 22/22F Rim/SVR exit devices are compatible with AD200 and AD250-993 exit trims.
- Falcon 25 Rim exit device is compatible with AD200 and AD250-993 exit trims.
- Yale 7110-SVR is NOT compatible with AD-Series products
- AD-series and CO-series exits use a rotational input to unlock the door, exit devices that require a lifting motion istead of rotational, are NOT compatible with AD-series exit devices.
Do CO locks come with a Door Position Switch (DPS) switch?No, all CO locks do not come with the DPS switch unless the lock is ordered as privacy function 40, since the CO can't be changed or re-cla..
Download Link for: CO-100 Offline Lock User Guide - EnglishDownload Link for: CO-Series Cylindrical Installation InstructionsDownload Link for: CO-Series Mortise Insta..
The customer would need to order the spacer that fits between the door and the the lock base plate, to space the lock over the surface vertical rod. Otherwise the 993-R is the same lock as th..
An AD or CO lock with keypad will go into lockout mode and stops responding to key presses after 20 wrong key presses and then the lock remains in timeout and unresponsive for 30 seconds.Wait 30 se..
To remove an AD or CO series lever requires a push pin type Pin Wrench (included with all new locks) or Lever Removal Tool used to depress the knob stop pin.The knob stop pin is located through a ..
What are the AD / CO Steel Lever Set Screw details?AD/CO Steel Lever Set Screw, Tapered Point AD/CO 993: 1/4-28 x 1/2' &..
Where can I find a parts listing for CO series Locks? (Includes CO-100, CO-200, CO-220, CO-250)Download link for: CO Series Service Manual
products
Support
View All Support
CO-100 Keypad Programmable Lock
Part of the CO Series, this simple offline, keypad-entry lock is designed for up to 500 unique users using PIN code entry only. CO-100 is an economic alternative anytime there is a desire to minimize key distribution
CO-100 models are designed for use as easy to manage, low maintenance locks that use 3-6 digit PIN codes as credentials. Administrator level users can program it right at the door to add or delete user PIN codes or change preferences or functions at any time.
They are ideal for:
Visitor pass through/common areas
Vestibules or reception area doors controlled by remote release
Pool gates, breezeways and other outdoor applications
Maintenance areas
Supply closets/equipment rooms
Workout rooms
Restrooms/bathrooms
Dressing/fitting rooms
Maternity/nursing rooms
Other private rooms needing occupancy indication
Cylindrical, mortise, and exit trim chassis options are available as well as a wide variety of finishes and levers to suite with existing hardware. Mechanical key override is standard and compatible with cylinders from Schlage and other popular brands. The CO-Series is also compatible with many popular brands of exit devices.
In accordance with California PROP65 -
WARNING: Cancer & Reproductive Harm www.P65Warnings.ca.gov
Security
Helps to minimize key distribution to ensure the integrity of the key system over time
Classroom/storeroom function can be used to secure doors and gates indoors and out
Office and privacy function options for application on interior or perimeter doors
Available with Schlage’s full complement of key cylinder options including levers designed for compatibility with many other OEM cylinders
Compatible with most major brands of exit devices
Efficiency
Manages up to 500 unique 3-6 digit PIN codes with user rights stored on the lock
Utilize existing master key system
Low lifetime cost of ownership
Convenience
PIN codes can be issued and revoked quickly, right at the keypad
Normal, toggle, pass through, and freeze programming options
Occupancy indication programmable option available on privacy function locks
Up to 2 years battery life with status indicator for easy maintenance
In accordance with California PROP65 -
WARNING: Cancer & Reproductive Harm www.P65Warnings.ca.gov
Certifications
ANSI/BHMA A156.25 full outdoor (70 function)
ANSI/BHMA, Grade 1
UL 294
UL 10C
UL Canada
FCC Part 15
ADA
RoHS
Meets or exceeds
Cylindrical - ANSI/BHMA A156.2, Series 4000, Grade 1
Mortise - ANSI/BHMA A156.13, Series 1000, Grade 1
Exit trim - ANSI/BHMA A156.3
In accordance with California PROP65 -
Rim Exit Device Definition
WARNING: Cancer & Reproductive Harm www.P65Warnings.ca.gov
For full electronic specifications please reference the CO-100 data sheet.
Reader options
Keypad only
User verification
Capable of credential verification <1 second
Up to 500 users
Remote release available on Office function locks
Programming options
Basic users can:
Enter assigned PIN code to unlock door momentarily from normally locked state
Managers can:
Be assigned toggle code priveges to change the lock to an unlocked state and back when desired
Assign or delete basic user PIN codes
Administrators can:
Assign or delete basic user PIN codes
Change programming codes
Adjust desired relock delay from 1-120 seconds
Put lock into freeze state that cannot be toggled
Use a pass-through code to momentarily unlock regardless of current state
Disable or enable remote features like release or occupancy indication where available
Additional
Programmable privacy function option provides lighted occupancy indication when in use
Battery life - up to 2 years with 4 AA batteries
Exterior Temp: -31° to 151°F (-35° to 66°C)
Interior Temp: 32° to 120°F (0° to 49°C) (battery)
Humidity: 0 - 100% non-condensing
In accordance with California PROP65 -
WARNING: Cancer & Reproductive Harm www.P65Warnings.ca.gov
For full mechanical specifications please reference the CO-100 data sheet.
Chassis
Cylindrical
Mortise
Exit trim
Each offered with LED status indicator
Cylinder and keys
Standard keyway: Schlage 6-pin Everest 29 S123 with two patented keys
Classic and restricted keyways, master keying and grand master keying options
Key-in-lever, FSIC, and SFIC cylinder options
Less cylinder options to fit common Sargent®, Corbin Russwin®, Medeco®, Yale® and Falcon® cylinders
Functions
70 Classroom/Storeroom
50 Office with option for remote (wired) release
40 Privacy with programmable occupancy indication option
Schlage and Falcon are trademarks of Allegion plc, its subsidiaries and/or affiliates in the United States and other countries. All other trademarks are the property of their respective owners.
Weather-resistant for interior and perimeter applications
Suiting
Designed to create an attractive and cohesive building-wide look when paired with other Schlage, Von Duprin or LCN devices. Click here to see the full line of designs and finishes.
In accordance with California PROP65 -
WARNING: Cancer & Reproductive Harm www.P65Warnings.ca.gov
Category information
Schlage 22 Rim Exit Device User Manual Download
Product information
Related product information
Technical resources
Installation instructions and user guides
Don't see the document you're looking for? Visit the Document Library for the full selection.
Schlage 22 Rim Exit Device User Manual Blue Light
In accordance with California PROP65 -
WARNING: Cancer & Reproductive Harm www.P65Warnings.ca.gov
Architecturally suited products
What Is Rim Exit Device
Related products
In accordance with California PROP65 -
WARNING: Cancer & Reproductive Harm www.P65Warnings.ca.gov